phyWAVE-KW22 Board

Support for the phyWAVE evaluation board. More...

Detailed Description

Support for the phyWAVE evaluation board.

Manufacturer

Designed and produced by PHYTEC Messtechnik GmbH, D-55129 Mainz. Homepage | Ordering information via mail at conta.nosp@m.ct@p.nosp@m.hytec.nosp@m..de

Overview

The phyNODE evaluation board consists of a phyWAVE module mounted on a common PCB with several sensor and actuator modules. The board provides 2 USB ports. The one next to the white imprint cmsis-dap is meant for development (debug and flash). The second one, next to the golden PHYTEC* imprint, is connected to the USB peripheral of the MCU and may be used by a firmware (currently not supported).

The implementation status of the phyWAVE and phyNODE peripherals are listed below. You can find links to the corresponding Pull Requests which may give you a code reference.

phyNODE board with equipped phyWAVE-KW2x processor/radio-module.

Note

The PCB-pieces with the mounted sensors can be separated from the evaluation board to capture sensor values from specific spatial points.

Pinout Reference

The board features an Arduino like header connector to mount shields. The spacing of the 4 pin rows is a bit offset, thus shields might not fit perfectly.

The pinout below shows the vendor specific naming and functionality. The actual pin configuration of the board for RIOT can be found in periph_conf.h.

Note

Not all signals and pins are compatible with Arduino Uno R3.

                            _X1____________________
                           |                   D15 |___DIO21, PE19, I2C0 SCL
                           |                   D14 |___DIO20, PE18, I2C0 SDA
                           |                  AREF |___AREF,  VCC3V3
                           |                  GND3 |___GND
                       X___| RESERVED          D13 |___DIO3,  PC5,  SPI0 SCK
                  VCC3V3___| IOREF             D12 |___DIO5,  PC7,  SPI0 MISO
                  nRESET___| RST TGTMCU        D11 |___DIO4,  PC6,  SPI0 MOSI
                  VCC3V3___| P3V3              D10 |___DIO2,  PC4,  SPI0 CS0
             P5V USB OUT___| P5V USB            D9 |___DIO9,  PD4,  PWM
               GND_________| GND2               D8 |___DIO6,  PD1
                       \___| GND1                  |
                       X___| P5_9V VIN          D7 |___DIO24, PA1,  PWM,  TDI2
                           |                    D6 |___DIO25, PA2,  PWM,  TDO2
DIO15, PE2, ADC         ___| A0                 D5 |___DIO11, PD6,  PWM
DIO16, PE3, ADC, TDO1   ___| A1                 D4 |___DIO29, PA19, TCLKIN
DIO12, PD7, ADC         ___| A2                 D3 |___DIO27, PA4,  PWM
DIO10, PD5, ADC         ___| A3                 D2 |___DIO17, PE4,  LLWU, TDI1
DIO13, PE0, ADC, I2CSDA ___| A4                 D1 |___DIO8,  PD3,  UART2 TX
DIO14, PE1, ADC, I2CSCL ___| A5                 D0 |___DIO7,  PD2,  UART2 RX
                            -----------------------
                            Arduino Uno R3 Connector

Implementation Status

Device	ID	Supported	Comments
MCU	MKW22D512	yes	mainline
phyWAVE board support	phyWAVE	yes	mainline
Low-level driver	GPIO	yes	mainline
	PWM	yes	mainline
	UART	yes	mainline
	I2C	yes	mainline
	SPI	yes	mainline
	USB-Device	yes	WIP
	RTT	yes	mainline
	RNG	yes	mainline
	Timer	yes	mainline
Radio Chip	integrated	yes	mainline
Humidity Sensor	HDC1000	yes	mainline
Pressure Sensor	MPL3115A2	yes	mainline
Tri-axis Accelerometer	MMA8652FC	yes	mainline
Magnetometer	MAG3110FCR1	yes	mainline
Light Sensor	TCS3772	yes	mainline
IR-Termopile Sensor	TMP006	yes	mainline
Capacitive Button	PCB	yes	mainline

Files
file	board.h
	Board specific definitions for the phyWAVE evaluation board.
file	gpio_params.h
	Board specific configuration of direct mapped GPIOs.
file	periph_conf.h