- Generated on Thu Nov 21 2024 05:52:12 by
1.9.8
Support for the xG23-PK6068A board. More...
Support for the xG23-PK6068A board.
The EFR32xG23 (xG23) Pro Kit is designed to support the development of Wireless IoT devices based on Sub-GHz wireless protocols. The Pro Kit includes a radio board that provides a complete reference design for the EFR32xG23 Wireless SoC, with the matching network for +20 dBm covering 868 to 915 MHz.
The main board contains an onboard J-Link debugger with a Packet Trace Interface and a Virtual COM port, enabling application development and debugging of the attached radio board as well as external hardware through an expansion header.
| MCU | EFR32ZG23 |
|---|---|
| Family | ARM Cortex-M33 |
| Vendor | Silicon Labs |
| Vendor Family | EFM32 Wireless Gecko |
| RAM | 64.0 KiB |
| Flash | 512.0 KiB |
| EEPROM | no |
| Frequency | up to 78 MHz |
| FPU | yes |
| MPU | no |
| DMA | 8 channels |
| Timers | 4x 16-bits, 1x 32-bits |
| ADCs | 16-bit ADC |
| UARTs | 1x USART, 3x EUSART |
| SPIs | 1x USART |
| I2Cs | 2x |
| Vcc | 1.71 V - 3.8 V |
| Datasheet | EFR32ZG23 |
| Manual | EFR32xG23 |
| Board Manual | xG23 |
| Board Schematic | Main Board BRD4001A, EFR32ZG23 Module BRD4210A |
This is the pinout of the expansion header on the right side of the board. PIN 1 is the bottom-left contact when the header faces you horizontally.
| PIN | PIN | ||
|---|---|---|---|
| 3V3 | 20 | 19 | RES |
| 5V | 18 | 17 | RES |
| PC7 | 16 | 15 | PC5 |
| PA9 | 14 | 13 | PA7 |
| PA8 | 12 | 11 | PA6 |
| PC0 | 10 | 9 | PD2 |
| PC3 | 8 | 7 | PA5 |
| PC2 | 6 | 5 | PA0 |
| PC1 | 4 | 3 | PA10 |
| VMCU | 2 | 1 | GND |
| Peripheral | Number | Hardware | Pins | Comments | Min. Power Mode |
|---|---|---|---|---|---|
| I2C | 0 | I2C0 | SDA: PC7, CLK: PC5 | EM1 | |
| SPI | 0 | USART0 | MOSI: PC1, MISO: PC2, CLK: PC3 | PC4 used as CS for Serial Flash | EM1 |
| Timer | 0 | TIMER0 | Default ztimer backend | EM1 | |
| 1 | LETIMER0 | EM3 | |||
| UART | 0 | EUSART1 | RX: PA9, TX: PA8 | Default STDIO output | EM1 |
| ADC_LINE | 0 | IADC0 | IN+: PA10, IN-: GND | Single-ended, V_ref: 2 * 1.21V | EM1 |
| 1 | IADC0 | IN+: PA0, IN-:PA5 | Differential, V_ref: 2 * 1.21V | EM1 |
| Peripheral | Mapped to | Pin | Comments |
|---|---|---|---|
| Button | PB0 | PB1 | |
| PB1 | PB3 | ||
| LED | LED0 | PB2 | Yellow LED |
| LED1 | PD3 | Yellow LED |
| Device | ID | Supported | Comments |
|---|---|---|---|
| MCU | EFR32ZG | yes | Power modes supported |
| Low-level driver | ADC | no | |
| Flash | yes | ||
| GPIO | yes | Interrupts are shared across pins (see reference manual) | |
| HW Crypto | partially | Only hwrng | |
| I2C | yes | ||
| PWM | no | ||
| RTC | no | As RTT or RTC | |
| SPI | partially | Only master mode | |
| Timer | yes | ||
| UART | yes | ||
| LCD driver | LS013B7DH03 | yes | Sharp Low Power Memory LCD via the U8g2 package |
| Temperature + humidity sensor | Si7021 | yes | Silicon Labs Temperature + Humidity sensor |
To flash, SEGGER JLink is required.
Flashing is supported by RIOT-OS using the command below:
To run the GDB debugger, use the command:
Or, to connect with your own debugger:
Silicon Labs' EMLIB: zlib-style license (permits distribution of source).
Files | |
| file | board.h |
| Board specific definitions for the xG23-PK6068A. | |
| file | gpio_params.h |
| Board specific configuration of direct mapped GPIOs. | |
| file | periph_conf.h |
| Configuration of CPU peripherals for xG23-PK6068A board. | |
1.9.8