periph_conf.h

Go to the documentation of this file.

/*
 * SPDX-FileCopyrightText: 2019 Benjamin Valentin
 * SPDX-License-Identifier: LGPL-2.1-only
 */
 
#pragma once

 
/* This board provides an LSE */
#ifndef CONFIG_BOARD_HAS_LSE
#define CONFIG_BOARD_HAS_LSE    1
#endif
 
/* This board provides an HSE */
#ifndef CONFIG_BOARD_HAS_HSE
#define CONFIG_BOARD_HAS_HSE    1
#endif
 
/* The HSE provides a 25MHz clock */
#ifndef CONFIG_CLOCK_HSE
#define CONFIG_CLOCK_HSE               MHZ(25)
#endif
 
#include "clk_conf.h"
#include "cfg_i2c1_pb8_pb9.h"
#include "cfg_timer_tim5.h"
#include "cfg_usb_otg_fs.h"
 
#ifdef __cplusplus
extern "C" {
#endif

static const uart_conf_t uart_config[] = {
    {
        .dev        = USART2,
        .rcc_mask   = RCC_APB1ENR_USART2EN,
        .rx_pin     = GPIO_PIN(PORT_A, 3),
        .tx_pin     = GPIO_PIN(PORT_A, 2),
        .rx_af      = GPIO_AF7,
        .tx_af      = GPIO_AF7,
        .bus        = APB1,
        .irqn       = USART2_IRQn,
#ifdef MODULE_PERIPH_DMA
        .dma        = DMA_STREAM_UNDEF,
        .dma_chan   = UINT8_MAX,
#endif
    },
    {
        .dev        = USART1,
        .rcc_mask   = RCC_APB2ENR_USART1EN,
        .rx_pin     = GPIO_PIN(PORT_A, 10),
        .tx_pin     = GPIO_PIN(PORT_A, 9),
        .rx_af      = GPIO_AF7,
        .tx_af      = GPIO_AF7,
        .bus        = APB2,
        .irqn       = USART1_IRQn,
#ifdef MODULE_PERIPH_DMA
        .dma        = DMA_STREAM_UNDEF,
        .dma_chan   = UINT8_MAX,
#endif
    },
};
 
/* assign ISR vector names */
#define UART_0_ISR          isr_usart2
#define UART_1_ISR          isr_usart1
 
/* deduct number of defined UART interfaces */
#define UART_NUMOF          ARRAY_SIZE(uart_config)

static const pwm_conf_t pwm_config[] = {
    {
        .dev      = TIM2,
        .rcc_mask = RCC_APB1ENR_TIM2EN,
        .chan     = { { .pin = GPIO_PIN(PORT_A, 15),          .cc_chan = 0 },
                      { .pin = GPIO_PIN(PORT_B, 3),  /* D3 */ .cc_chan = 1 },
                      { .pin = GPIO_PIN(PORT_B, 10), /* D6 */ .cc_chan = 2 },
                      { .pin = GPIO_UNDEF,                    .cc_chan = 0 } },
        .af       = GPIO_AF1,
        .bus      = APB1
    },
    {
        .dev      = TIM3,
        .rcc_mask = RCC_APB1ENR_TIM3EN,
        .chan     = { { .pin = GPIO_PIN(PORT_B, 4), /* D5 */ .cc_chan = 0 },
                      { .pin = GPIO_PIN(PORT_C, 7), /* D9 */ .cc_chan = 1 },
                      { .pin = GPIO_PIN(PORT_C, 8),          .cc_chan = 2 },
                      { .pin = GPIO_PIN(PORT_C, 9),          .cc_chan = 3 } },
        .af       = GPIO_AF2,
        .bus      = APB1
    },
};
 
#define PWM_NUMOF           ARRAY_SIZE(pwm_config)

static const spi_conf_t spi_config[] = {
    {   /* U3 - SPI flash */
        .dev      = SPI1,
        .mosi_pin = GPIO_PIN(PORT_A, 7),
        .miso_pin = GPIO_PIN(PORT_A, 6),
        .sclk_pin = GPIO_PIN(PORT_A, 5),
        .cs_pin   = GPIO_PIN(PORT_A, 4),
        .mosi_af  = GPIO_AF5,
        .miso_af  = GPIO_AF5,
        .sclk_af  = GPIO_AF5,
        .cs_af    = GPIO_AF5,
        .rccmask  = RCC_APB2ENR_SPI1EN,
        .apbbus   = APB2
    },
    {
        .dev      = SPI2,
        .mosi_pin = GPIO_PIN(PORT_B, 15),
        .miso_pin = GPIO_PIN(PORT_B, 14),
        .sclk_pin = GPIO_PIN(PORT_B, 13),
        .cs_pin   = GPIO_PIN(PORT_B, 12),
        .mosi_af  = GPIO_AF5,
        .miso_af  = GPIO_AF5,
        .sclk_af  = GPIO_AF5,
        .cs_af    = GPIO_AF5,
        .rccmask  = RCC_APB1ENR_SPI2EN,
        .apbbus   = APB1
    },
    {
        .dev      = SPI3,
        .mosi_pin = GPIO_PIN(PORT_B, 5),
        .miso_pin = GPIO_PIN(PORT_B, 4),
        .sclk_pin = GPIO_PIN(PORT_B, 3),
        .cs_pin   = GPIO_PIN(PORT_A, 15),
        .mosi_af  = GPIO_AF6,
        .miso_af  = GPIO_AF6,
        .sclk_af  = GPIO_AF6,
        .cs_af    = GPIO_AF6,
        .rccmask  = RCC_APB1ENR_SPI3EN,
        .apbbus   = APB1
    },
};
 
#define SPI_NUMOF           ARRAY_SIZE(spi_config)

static const adc_conf_t adc_config[] = {
    {GPIO_PIN(PORT_A, 0), 0, 0},
    {GPIO_PIN(PORT_A, 1), 0, 1},
    {GPIO_PIN(PORT_A, 4), 0, 4},
    {GPIO_PIN(PORT_B, 0), 0, 8},
    {GPIO_UNDEF, 0, 18} /* VBAT */
};
 
#define VBAT_ADC            ADC_LINE(4) 
#define ADC_NUMOF           ARRAY_SIZE(adc_config)
 
#ifdef __cplusplus
}
#endif