Default configuration parameters for the lm75 sensors. More...
Detailed Description
Default configuration parameters for the lm75 sensors.
Definition in file lm75_params.h.
Include dependency graph for lm75_params.h:Go to the source code of this file.
| #define | LM75_PARAM_I2C I2C_DEV(0) |
| I2C BUS used. | |
| #define | CONFIG_LM75_I2C_ADDR (0x48) |
| 7-bit I2C slave address: 1-0-0-1-A2-A1-A0, where the last three bits A2, A1, A0 are defined by the voltage level on the ADDR pin | |
| #define | CONFIG_OPERATION_MODE NORMAL_MODE |
| Normal Mode is the default. | |
| #define | CONFIG_THERMOSTAT_MODE COMPARATOR_MODE |
| Comparator Mode is the default. | |
| #define | CONFIG_OS_POLARITY OS_ACTIVE_LOW |
| OS pin active on low is the default. | |
| #define | CONFIG_FAULT_QUEUE FAULT_1 |
| One Fault is the default. | |
| #define | LM75_PARAM_INT GPIO_UNDEF |
| Pin used for Interrupts defined by the board. | |
| #define | LM75A_CONV_RATE (100) |
| temperature register updated every 100ms | |
| #define | LM75A_OS_RES (5) |
| resolution in 0.5ºC | |
| #define | LM75A_OS_MULT (10) |
| Must multiply by 10 to get temp in ºC. | |
| #define | LM75A_OS_SHIFT (7) |
| Only the 9 most significant bits are needed. | |
| #define | LM75A_TEMP_RES (125) |
| resolution in 0.125ºC | |
| #define | LM75A_TEMP_MULT (1000) |
| Must multiply by 1000 to get temp in ºC. | |
| #define | LM75A_TEMP_SHIFT (5) |
| Only the 11 most significant bits are needed. | |
| #define | TMP1075_OS_RES (625) |
| resolution in 0.0625ºC | |
| #define | TMP1075_OS_MULT (10000) |
| Must multiply by 10000 to get temp in ºC. | |
| #define | TMP1075_OS_SHIFT (4) |
| Only the 12 most significant bits are needed. | |
| #define | TMP1075_TEMP_RES (625) |
| resolution in 0.0625ºC | |
| #define | TMP1075_TEMP_MULT (10000) |
| Must multiply by 10000 to get temp in ºC. | |
| #define | TMP1075_TEMP_SHIFT (4) |
| Only the 12 most significant bits are needed. | |
| #define | CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_27H |
| Default conv rate is 27.5ms. | |
| #define | TMP1075_CONV_RATE (28) |
| Default conversion rate is 27.5 ms. | |
| static const lm75_params_t | lm75_params [] |
| LM75 power-up configuration. | |
Macro Definition Documentation
◆ CONFIG_FAULT_QUEUE
| #define CONFIG_FAULT_QUEUE FAULT_1 |
One Fault is the default.
Definition at line 95 of file lm75_params.h.
◆ CONFIG_LM75_I2C_ADDR
| #define CONFIG_LM75_I2C_ADDR (0x48) |
7-bit I2C slave address: 1-0-0-1-A2-A1-A0, where the last three bits A2, A1, A0 are defined by the voltage level on the ADDR pin
Default I2C address
Definition at line 39 of file lm75_params.h.
◆ CONFIG_OPERATION_MODE
| #define CONFIG_OPERATION_MODE NORMAL_MODE |
Normal Mode is the default.
Definition at line 50 of file lm75_params.h.
◆ CONFIG_OS_POLARITY
| #define CONFIG_OS_POLARITY OS_ACTIVE_LOW |
OS pin active on low is the default.
Definition at line 74 of file lm75_params.h.
◆ CONFIG_THERMOSTAT_MODE
| #define CONFIG_THERMOSTAT_MODE COMPARATOR_MODE |
Comparator Mode is the default.
Definition at line 62 of file lm75_params.h.
◆ CONFIG_TMP1075_CONV_RATE_REG
| #define CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_27H |
Default conv rate is 27.5ms.
Definition at line 135 of file lm75_params.h.
◆ LM75_PARAM_I2C
| #define LM75_PARAM_I2C I2C_DEV(0) |
I2C BUS used.
Definition at line 32 of file lm75_params.h.
◆ LM75_PARAM_INT
| #define LM75_PARAM_INT GPIO_UNDEF |
Pin used for Interrupts defined by the board.
Definition at line 100 of file lm75_params.h.
◆ LM75A_CONV_RATE
| #define LM75A_CONV_RATE (100) |
temperature register updated every 100ms
Definition at line 103 of file lm75_params.h.
◆ LM75A_OS_MULT
| #define LM75A_OS_MULT (10) |
Must multiply by 10 to get temp in ºC.
Definition at line 106 of file lm75_params.h.
◆ LM75A_OS_RES
| #define LM75A_OS_RES (5) |
resolution in 0.5ºC
Definition at line 105 of file lm75_params.h.
◆ LM75A_OS_SHIFT
| #define LM75A_OS_SHIFT (7) |
Only the 9 most significant bits are needed.
Definition at line 107 of file lm75_params.h.
◆ LM75A_TEMP_MULT
| #define LM75A_TEMP_MULT (1000) |
Must multiply by 1000 to get temp in ºC.
Definition at line 109 of file lm75_params.h.
◆ LM75A_TEMP_RES
| #define LM75A_TEMP_RES (125) |
resolution in 0.125ºC
Definition at line 108 of file lm75_params.h.
◆ LM75A_TEMP_SHIFT
| #define LM75A_TEMP_SHIFT (5) |
Only the 11 most significant bits are needed.
Definition at line 110 of file lm75_params.h.
◆ TMP1075_CONV_RATE
| #define TMP1075_CONV_RATE (28) |
Default conversion rate is 27.5 ms.
Definition at line 136 of file lm75_params.h.
◆ TMP1075_OS_MULT
| #define TMP1075_OS_MULT (10000) |
Must multiply by 10000 to get temp in ºC.
Definition at line 113 of file lm75_params.h.
◆ TMP1075_OS_RES
| #define TMP1075_OS_RES (625) |
resolution in 0.0625ºC
Definition at line 112 of file lm75_params.h.
◆ TMP1075_OS_SHIFT
| #define TMP1075_OS_SHIFT (4) |
Only the 12 most significant bits are needed.
Definition at line 114 of file lm75_params.h.
◆ TMP1075_TEMP_MULT
| #define TMP1075_TEMP_MULT (10000) |
Must multiply by 10000 to get temp in ºC.
Definition at line 116 of file lm75_params.h.
◆ TMP1075_TEMP_RES
| #define TMP1075_TEMP_RES (625) |
resolution in 0.0625ºC
Definition at line 115 of file lm75_params.h.
◆ TMP1075_TEMP_SHIFT
| #define TMP1075_TEMP_SHIFT (4) |
Only the 12 most significant bits are needed.
Definition at line 117 of file lm75_params.h.
Variable Documentation
◆ lm75_params
|
static |
LM75 power-up configuration.
Definition at line 171 of file lm75_params.h.
