RE-Mote Revision B

Support for the RE-Mote board Revision B. More...

Detailed Description

Files

file  remote-revb/include/board.h
 Board specific definitions for the RE-Mote board Revision B.
 
file  boards/remote-revb/include/periph_conf.h
 Peripheral MCU configuration for the RE-Mote board revision B.
 

Functions

void board_init (void)
 Initialize board specific hardware, including clock, LEDs and std-IO.
 

LED pin definitions

#define LED0_PIN   GPIO_PIN(3, 4)
 
#define LED1_PIN   GPIO_PIN(1, 7)
 
#define LED2_PIN   GPIO_PIN(1, 6)
 
#define LED0_MASK   (1 << 4)
 
#define LED1_MASK   (1 << 7)
 
#define LED2_MASK   (1 << 6)
 
#define LED0_ON   (GPIO_D->DATA |= LED0_MASK)
 
#define LED0_OFF   (GPIO_D->DATA &= ~LED0_MASK)
 
#define LED0_TOGGLE   (GPIO_D->DATA ^= LED0_MASK)
 
#define LED1_ON   (GPIO_B->DATA |= LED1_MASK)
 
#define LED1_OFF   (GPIO_B->DATA &= ~LED1_MASK)
 
#define LED1_TOGGLE   (GPIO_B->DATA ^= LED1_MASK)
 
#define LED2_ON   (GPIO_B->DATA |= LED2_MASK)
 
#define LED2_OFF   (GPIO_B->DATA &= ~LED2_MASK)
 
#define LED2_TOGGLE   (GPIO_B->DATA ^= LED2_MASK)
 

User button pin definition

#define BTN0_PIN   GPIO_PIN(0, 3)
 

RF switch controlled by SW

Controls which RF interface goes to the RP-SMA external antenna

These values configure the required pin to drive the RF antenna switch, to either enable the sub-1Ghz RF interface (power-up the CC1200) or the 2.4GHz RF interface of the CC2538, both alternatively routed to a RP-SMA connector to allow using an external antenna for both cases.

Note it is also possible to enable both RF interfaces at the same time, by switching On the sub-1GHz RF interface, and placing an 0Ohm resistor (R19), to select between using a ceramic chip antenna (not mounted), or to connect and external antenna over a pigtail to the U.Fl connector (not mounted).

RF switch state:

  • LOW: 2.4GHz RF interface on RP-SMA connector, CC1200 powered-off.
  • HIGH: Sub-1GHz RF interface on RP-SMA connector.
#define RF_SWITCH_GPIO   GPIO_PD2
 
#define RF_SWITCH_SUB_GHZ   gpio_set(RF_SWITCH_GPIO)
 
#define RF_SWITCH_2_4_GHZ   gpio_clear(RF_SWITCH_GPIO)
 
#define RF_SWITCH_TOGGLE   gpio_toggle(RF_SWITCH_GPIO)
 

Power management enable pin

#define SHUTDOWN_EN_GPIO   GPIO_PD1
 

CC1200 SPI and pins definitions

#define CC1200_SPI_DEV   SSI0
 
#define CC1200_MOSI_GPIO   GPIO_PB1
 
#define CC1200_MISO_GPIO   GPIO_PB3
 
#define CC1200_SCLK_GPIO   GPIO_PB2
 
#define CC1200_CSN_GPIO   GPIO_PB5
 
#define CC1200_RESET_GPIO   GPIO_PC7
 
#define CC1200_GPD0_GPIO   GPIO_PB4
 
#define CC1200_GPD2_GPIO   GPIO_PB0
 

Onboard micro-sd slot pin definitions

#define SDCARD_SPI_PARAM_SPI   SPI_DEV(1)
 
#define SDCARD_SPI_PARAM_CS   GPIO_PIN(0,7)
 
#define SDCARD_SPI_PARAM_CLK   GPIO_PIN(2,4)
 
#define SDCARD_SPI_PARAM_MOSI   GPIO_PIN(2,5)
 
#define SDCARD_SPI_PARAM_MISO   GPIO_PIN(2,6)
 
#define SDCARD_SPI_PARAM_POWER   GPIO_PIN(0,6)
 
#define SDCARD_SPI_PARAM_POWER_AH   false